Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat panda key fob replacement (click this link here now) 500 is a great way to unlock the doors and start the car. There are a myriad of reasons the fob could stop working. These include a dead coin battery, damaged receiver module, water damage issues, or interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't function is due to an inactive battery. Modern key fobs have a very limited range of operation, and must be within a few feet of the vehicle to function. If you're far from your vehicle and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one from a reputable brand such as Panasonic Duracell or Energizer. They are usually available at your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while standing close to your Fiat 500. The car should blink its parking lights, and the key fob should work the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it could have water damage that prevents it from communicating with the receiver module in your car. Water damage can happen in a variety of ways, such as simply splashing or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a bag of rice to draw out the moisture. If that doesn't work, the fob might need to be reprogrammed by an experienced auto locksmith or dealer.

Water Damage

While the fob has some rubber seals that keep water out of the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. Getting the fob wet is not an ideal choice however, if you drop it in an empty cup of water, or do not remember to remove it from your pants pocket before running the washing machine Don't give up hope.

First take the battery off the fob. Before replacing the battery clean the electronic chip with isopropyl or similar products. Then, fiat panda key fob replacement test the fob to test if it works. If the fob doesn't work, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and has not been programmed to work with your vehicle it is necessary to replace it completely. This is a straightforward process that can be carried out by a professional locksmith for automotive use. The locksmith will require the key to be cut to match your car's ignition. They will also need to reprogram the fob to your car's system. This is a simple and cost-effective process that can usually be completed the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote's range is of 30 feet. Therefore, in the event that you are far away from your vehicle it won't be able to respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as a "button" or "watch") and your fob doesn't function It could be because of an internal circuit board issue. In the majority of cases, reprogramming your fob will resolve this problem. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, they could stop the coin battery from sitting properly and can cause your remote to malfunction.

In rare instances, the fob could be out of connection with your vehicle as a result of hardware or software issues. This can cause a major issue, but you are able to often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain instances the software might require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This could occur if the key fob is near an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob could not work because of a problem with the buttons or water damage, or damage how to program fiat 500 key fob the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the 12 volt battery for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the car's computer. This could help you get your key fob to function again. If the issue persists, you should consult a certified technician. They can identify the exact cause of problems.