Cat flaps let your pet move around as they please without you needing to let him in or out. They can also help prevent your cat from toileting in the house.

Installing a cat flap on a door panel made of Upvc is much easier than in a glass door, however it will require some expertise and the appropriate tools.

Measure the Door

The installation of a cat flap inside a door can be tricky but if you use the correct type of cat flap, take your time and follow the steps provided it shouldn't be too difficult. We will show you how to draw the shape, use a jigsaw to cut out the door's area and then finish the job by attaching the cat flap to the door. This will ensure that the flap remains in place and shields the door from rain and wind causing damage.

To determine the size of the cat flap that you require, take a measurement of the width of your pet. This will ensure that the flap is large enough to let your pet enter and leave the house without having to open or close the door every time, yet small enough to stop them from going too far in either direction.

Once you have the measurements you can mark the area on the door where the template should be positioned, typically this is done using an X, however some kits include a drawing that shows where to drill, if yours does then stick it to the door and use a pencil to draw around the door. If your door has a sill or moulding at the bottom, be sure that you leave enough space between your cat and the moulding or sill.

Set a square to check that you're cutting properly and to make sure the hole is a perfect rectangle shape. Once you are happy with the result, you can begin removing the remaining door material. If you have a set square then make use of it to verify whether you're cutting in the right way and to ensure that the hole is in a rectangle shape, once you are happy with this you can start to remove the remaining door material.

Draw a Line

The cat flap allows you to let your pet in and outside without having to worry about unwanted visitors or unwelcome gifts. It also reduces drafts and helps keep the temperature in your home steady. The installation of a cat flap your door might seem difficult to those who haven't done it before. Many people call a professional carpenter or joiner to complete the job. It is an option, but you can do it yourself if your tools are right and the directions are adhered to.

While this is far simpler with a wooden door, it is still possible to do this in uPVC doors, though you must be careful to avoid damaging the doors, as this can cause damage to your warranty. First, you must measure the door to ensure it will accommodate the new cat-flap. If you have a standard uPVC panel it should be a breeze. However in the case of made of composite or another kind of door, you might need to be more careful.

Next, you will need to determine the height of your belly for your cat. This is the height between the floor and the bottom of your cat's stomach. You will need to find an area at the entrance that will allow your pet to comfortably pass through. Once you have this information, you will have to draw the area using a pencil and a spirit level to ensure that the hole you will make will be suitable for your cat.

Once you've marked the area, it's now time to cut the hole. You will need to use a jigsaw and it is essential to be patient to ensure that the cuts are clean and smooth rather than uneven and rough, since this could damage your door. Be sure to wear safety glasses and a dust protection mask whenever working with the jigsaw as breathing in the dust could be harmful to your health. After you've finished the cutting, you'll need to smooth out the edges of the hole using sandpaper, so that your cat flap can be fitted easily into place.

Cut a hole

Getting a cat flap fitted into an existing door panel or double glazing sealed unit is quite difficult. It is tempting to do it yourself, but unless you have plenty of expertise in DIY, it's recommended to hire a professional to do the task for you. A mistake could not only be ugly and unattractive, but could also be a security threat. It could allow cold air to enter when the cat is outside and hot air out when inside.

The hole's location should be marked on the door using the help of a pencil and a spirit level. This will ensure it is properly positioned and is flush with the rest of the door. Make sure you have sandpaper on hand to smooth any rough edges.

Wear the safety equipment you require when working with a power tool. If you're worried about the noise, you can get a jigsaw with a cord that is quieter and more user-friendly.

It is best to only remove the material that is required to fit the flap. It is necessary to leave a little extra material to cover the wall of the cat flap cost near me flap. However cutting away too much could cause problems or even damage the door frame.

A door made of upvc may include a metal frame, or a panel inside that will interfere with the microchip cat flap and in this case you'll need to cut an oversize hole to ensure the metal doesn't come into contact with the the cat flap, if this is done it is crucial to fill in the oversize gap and render it watertight.

If you are fitting the cat flap onto a upvc door or double glazed window with a frame made of metal, you'll need to speak to a specialist who can provide you with a new glass pane that already has the hole for the Cat Flap In Upvc Door Panel flap already drilled in it. This will be less expensive than fitting the flap into an existing pane that was not made for this purpose.

Install the Flap

Cat flaps allow your pet to move around whenever they want, allowing them the ability to unwind inside the house when they feel like it. However, if you own an uPVC door it can be difficult to put in a cat flap cost near me flap, especially if you don't own a glass pane that can be cut for one. Luckily, if you're happy to purchase and install a half-glazed replacement uPVC panel then it is possible to fit a cat flap to the doors. It's not as simple as simply cutting a hole through the door, however there are some things you'll need to do first to make sure it's secure.

A composite, upvc door panel with cat flap or GRP door panel is typically composed of a thin plastic skin which is bonded to an insulating polystyrene core. The material is quite fragile and care should be taken when cutting through it to avoid causing damage. This kind door comes with a template that you can use to make the hole.

Once you've marked the opening in your front door, it is time to put in the cat flap. You can choose from a wide range of options, from simple push-button flaps to microchip-activated ones that only let your pet in. However, regardless of what kind of cat flap you pick, it is essential to ensure that your cat can use the flap without becoming trapped in the weather.

It is a good idea to opt for circular fittings instead of one that is square, since circles are more securely cut into the door glass. This is because square holes are more likely to break the glass when they're drilled. It's also a safer option as you don't risk having to drill into toughened glass that could shatter and hurt your pet or family members. This is especially important if there are elderly or children at home who might be injured by glass shattering.