How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking then it's likely that they need some maintenance. It is possible that you need to clean and lubricate them or adjust them. The problem may be caused by a loose screw on the top pivot or by the top guide roller.

This kit comes with all the hardware needed to return your bi fold door repairs-bi fold door repair closet door to its optimal performance.

Take the door off

Installing a set of internal bifold doors might appear to be a complicated and complicated project however, it's actually easy for DIYers with a little experience. Moving the frame isn't a problem but the trick is getting the doors to fold and close quickly and accurately. As bifold doors are complex machines, they may need some tuning to keep working properly. It could be as simple as tightening a screw, or as complex as removing and replacing the pivot pin or roller.

It is usually possible to fix these issues by making just a few minor adjustments, without having to take out the doors. It is possible that your bifold doors are sliding or scraping the floor, or slipping off track. The solution to these issues isn't difficult. With three simple steps your bifold door roller replacement doors can be back on track in the blink of an eye.

One of the most frequent problems that internal bifold doors have to face is the tendency to slide out of alignment. This could be due to loose screws, holes in the anchor/pivot pins or simply a door that isn't aligned properly. In the majority of instances, you can fix this with a few easy adjustments, but if the door isn't moving at all it may need to be removed and replaced.

To open the door to open it, you'll require an screwdriver and perhaps two pliers (to aid in loosening any pins on the pivot that are stuck). The screwdriver is used to release any locking levers that are on the bottom pivot bracket and the pliers let you wiggle the pin to release it and then take it off.

After the top roller is loose, you should be able to lift the door and swivel it down, allowing you to take it off of its track and pivot brackets. It's usually quite simple however be careful not to let the door hit against the frame of the door. Then, you can sand down the edges of the door to smooth it. Then paint or refinish the door as required.

Take off the Roller Guide

This spring-loaded roller guide mounts on the top of the bifold door to assist with smooth operation. It is specifically designed specifically for Kenna frames, and will fit door panels from 1 inch to 1-3/8 inch thick. It is made from nylon, steel, and other components and can replace a worn-out or damaged guide.

Take out any screws that are holding the guide to the roller using the screwdriver. Then, use your hands to remove it of the frame. It may take some effort, so let an assistant help you keep the door in place while you remove it.

After removing the old guide, carefully cut off the remaining finish off the foot of the guide with a razor to separate it from blank rod. This will make the guide foot easier to remove, and also prevent any damage. The foot is extremely sharp, and it could cut or nick fingers.

It is possible to use some force to remove the guide, but you must be careful not to break or chip the foot. After you have separated the guide from the rod blank, be sure to take out all of the threads and epoxy that remain where it was attached. This will help prevent any future issues with the guide.

After you have removed the guide, test out your new guide by putting it in its permanent location and applying a few rotations of masking tape or a type of guide tubing to hold it in the correct position. This will allow you double examine the guide's spacing and alignment to make sure everything is set up properly. It doesn't matter if you're looking at it from a distance or using the dependable CRB Spine Finder and Deflection System, this step is important to prevent any issues in the future.

If the guide is set properly and functions according to its intended function the next step will be to put the door back in its place. Make sure that any screws or pins that you loosened or removed should be replaced and tightened appropriately after you've finished.

Take the Bottom Pivot off.

Bifold doors can be a stunning feature for a home, but they sometimes need to be tweaked or adjusted to ensure they remain in good shape. Certain issues can be solved with the doors still in place. Others will require that the doors be removed. This guide will demonstrate how to remove the bifold door replacement internal door pins, rollers, and pivots.

The first step is to gather your tools. You will save yourself some frustration if you gather all your tools in advance. You'll require a screwdriver, pliers and maybe a wrench. A basic set of tools can be purchased at a reasonable cost from your local hardware store. It's also a good idea to have some wood glue in your kit. This is useful if you need to put the rollers in place.

Once you've got the tools, begin by opening the bifold doors, and then loosening the top track bracket with your screwdriver. Once the bracket is loose, you should be able to lift the door off the top track. It could take a little small amount of jiggling, but it should be able to pop right off the track.

The pivot on the bottom of the frame will have to be removed. It is best to do this from the outside of your home So, make sure to close any internal doors that you are able to open. This will make it much easier to do than trying to work on the inside. If the track at the bottom appears good, you can simply lift the door and remove the track.

You will need to replace the track if it is damaged. Hardware stores sell replacement tracks for bifold doors as well as swinging closet doors. If the track is seriously damaged, you may have to replace it completely.

After your track has been repaired or replaced You'll need to check the doors for their proper operation. Check that the doors can be moved into and out of their position effortlessly. You'll want to make sure that the edges of your door are parallel to the frame when it's closed. If they aren't, then you'll need to adjust the top pivot bracket and tighten or loosen the bottom set screw until the door's edge is perfectly aligned with the frame.

Replace the Roller

If they are installed properly the bifold doors can easily cover laundry nooks, pantries and closets. They are made up of two panels that hinge together and slide open on the track that is located at the frame's top. Over time the guides for the rollers can wear out and cause the doors to sag. Replacing the guide roller takes only a few minutes and a few basic tools.

The first step is to remove the roller guide from the door panel. This involves removal of the bottom pivot bolt and loosening the screw that holds the guide at its top. After the guide is removed then lift the door frame up and out of its track. Then, loosen the bolt that secures the top pivot bolt and employ the wrench to remove it from the hole in the top header of the door frame.

A top nylon replacement guide with a 7/8 inch diameter wheel and a steel base is available from Stanley, Cox or Acme. It is mounted on the top edge of a bifold door that is 1 to 1-3/8 inches thick and is spring loaded to self-adjust the upper track to ensure smooth sliding.

Bifold doors can also scratch against the floor as it opens and closes. This can happen after adding carpet or other flooring materials which require that the doors be raised slightly to allow clearance. Removing the pivot adjustment screw on the bottom and loosening the top track's mounting screws, and moving the anchor/pivot pin typically enough to resolve this issue.

A new set of top roller guides is a low-cost solution to a problem that could make your bifold doors difficult to operate. You can usually find them at your local hardware store in the door section, but they're also available online from a number of suppliers. You will also need a squeeze-clamp and a small container of Elmer's wood adhesive which can be found in big box stores. The clamp is used to keep the area being repaired shut after the glue has been placed in and dried.