How to Replace a Kia Sportage Replacement Key

The key in many Kia models has an entry system that is keyless into. The key can be compared to the remote control and can be replaced by a new one purchased from an kia ceed car key battery dealer or locksmith.

Key fobs can stop working for several reasons, including the battery of the coin is dead, worn buttons or buttons, water damage, signal interference, and a defective receiver module. Here are some suggestions to help you get your Kia sportage replacement key to work again.

How do you replace the remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote or a push-to-start one, or a standard metal key that is not equipped with an electronic transponder. This is particularly relevant if your car displays a message that the smart key or remote has low battery power.

It's a fairly simple process. In order to replace the key fob battery take the mechanical key from the hole in the back of the key fob. You then need to pry open the cover. A small screw will be located inside the key fob, which holds the battery in the correct position. Remove the old battery by removing the screw using a small screwdriver. Then, insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go if the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your kia sportage replacement key fob whenever your fingers start to get chilly or when you need to do some errands in Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your keys need to be programmed, you will need to be aware of the key code number that is stamped on the key code tag and keep the number in a secure place.

How do you replace a dead battery?

If the Kia key fob does not respond when you press the lock/unlock button, it is likely that the battery is low. A low battery could cause other issues like the check engine light turning on or a delay in cranking the engine. It is relatively easy to replace the key fob batteries with only the use of a few tools.

Before beginning the process ensure that your vehicle is off and that all doors are closed. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the metal key pops out. The key can be put into the driver door handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plier bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and then align the replacement battery to ensure its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After installing the new battery and turning the key fob on and off in the ignition until the door locks up. You can then test the kia transponder key's Key fob once more to ensure it is working correctly.

How do you replace the smart key

You can have an ordinary keyfob or Smart Key based upon the model of kia Rio key Sportage. The difference between the two is that the smart fob has tiny mechanical key blade tucked inside it, while the standard fob does not. Both key fobs come with an internal battery that will eventually require changing. Fortunately, it's a fairly simple process that takes just two minutes.

Be sure to turn off your Kia, and be on a flat or well-lit surface prior to when you begin. Also, keep in mind that there are small parts inside the fob that can be snagged if not vigilant.

The first step is to find the small release button that is located on the backside of the fob. It will be either a circular silver button or a rectangular slot. When you press it mechanical key blade, it will appear and you can then open the key fob.

Once the key fob is opened, take out the battery. The new battery is a the CR-2032, and it can be purchased on the internet or at your local auto parts shop. When you're done, the key fob should permit you to lock and unlock your vehicle even if it's not running.

How to replace the mechanical key?

The Kia key fob is an amazing convenience that lets us lock and unlock our vehicle with the touch of an button. Like all devices it is possible that the Kia key fob can have issues at times. There are solutions to address these issues and keep your key fobs running for an extended period of time.

One of the most frequently encountered problems is a low or dead battery. This could cause the fob to stop working entirely or even to stop working intermittently. If this is the problem you should replace the battery a new one.

If this isn't enough to resolve the problem you can try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage internal components, or scratch the plastic. Once open, carefully remove the old battery and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and check that it's functioning properly. Contact a dealer, or a locksmith to fix the issue in the event that the key fob is not working. To avoid lockouts in the future, make sure you get an emergency key that can be able to work with all trunk and door cylinders.