Replacing uPVC Window Handles

Changing upvc window handles is an easy job. It is crucial to ensure that the new handle fits inside the spindle cutout in the window mechanism.

If you follow the steps below any cockspur handle can fit in most windows. The step height of the handle is key.

What to Do You Look For?

Over time, uPVC handles on many windows in the UK may begin to show signs of wear and tear. When this happens, the window handle may become loose or difficult to operate, making it essential to replace it. This is a easy task that can be completed by anyone who is familiar with basic hand tools.

The first step is to make sure the handle is firmly fixed to the window frame, and is in a position that is open. The next step is to locate the screws or pins that secure the handle in place. They are usually on the inside of the handle and are removed using a screwdriver or pliers.

When the handle is loose it can be taken from its hinges by gently pulling it off. It is then necessary to find a replacement handle with the same design and size. This can be accomplished in an online store or in a DIY store. The process should take only five minutes, and you will need a screwdriver is all you need.

When replacing the handle on a uPVC handle It is crucial to take into consideration the step height. This is the distance from the base of the handle until it rests on the window frame. This is a typical measurement and you should confirm the height of the step before purchasing a replacement handle.

There are several sizes depending on the kind of handle. Inline handles for uPVC windows usually feature lug centers of 31mm as well as handles with cockspur with 43mm centres. Tilt-and-turn handles are common on uPVC windows. They have a special design which allows the window be tilted for ventilation, and then turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This makes it difficult to open. It is essential to ensure that the replacement handle is fitted with the same spindle as your original one.

Remove the old Handle

If your window handles are damaged or not properly fitted, they could cause double glazing handle-glazed windows to not open or close correctly. They could even become stuck. There are many reasons for this like general wear and tear or the corrosion of the metal handle. In these cases, it is important to find replacement upvc window handles as soon as possible to prevent further damage and loss of function.

When replacing the handles of windows made of upvc, you should remove the old handles from the window. Start by removing the screw by the handle while it is in the closed position. This should reveal another screw and once removed, you are able to begin to take off the handle itself. It is possible to make the task simpler by using an electric screwdriver.

It is also worth noting that the handles' screws could be hidden behind plastic caps, therefore it is a good idea to take the Stanley knife to the screw covers and take them off. After the handle has been removed, you should then examine the square cut out on the base of the handle to make sure that the new window lock handles will work with it. It is crucial to measure the spindle length on the old handle and compare it to the dimensions of the window mechanism spindle cutout.

The different kinds of window handles made from upvc include: Espag handles, which have a central screw and will turn left or right; Cranked handles which have two screws and are found on tilt and turn windows made of upvc; and Spade handles, that have an arm that is flat and can be placed on either side of the window. Once you have a suitable replacement, it's just a matter of screwing the handle into place and making sure that the spindle is correctly inserted into the lock mechanism. Once you have done this, tighten the handle to the window frame. The replacement upvc handle will now be secure.

Measure the Spindle

If you're replacing a Upvc window handle that has slipped off, it's likely because the spindle holding it in place has become loose or damaged. In some instances, you can tighten the spindle using pin or screw. In other situations, it will require replacement window handle completely. There are a variety of upvc handles for patio doors. They include espagnolette handles inline, cockspur handles, and tilt and turn handles. Each kind has a distinct method of installing and replacing the handle.

Before you purchase a new handle, it is essential to know the size of the handle that is currently in use. This will ensure that the handle fits the window in a proper manner and be the correct size. All handles are sized according to industry standards, making it easy to identify the correct size.

To determine the size of your handle first remove it from the window by turning it to an open position. Then, you should be able to see the size of the screw or pin that holds it. Then take the ruler or tape measure to determine the length of the spindle. Once you have the length of your spindle it is possible to buy a replacement of exactly the same length.

The step height of a upvc window handle is also important to consider when you are buying an alternative. The step height is measured from the base to the point at which the handle is placed on the frame. Typically, this is approximately 21mm for uPVC windows and 9mm for aluminum. Dropping objects into the gap will allow you to see how far the handle extends before it comes into contact with an obstruction.

Cockspur handles may have different backsets, based on the kind of window you want to install them in. Inline the espag handle heights range from 43mm from centre to centre (two fixing points). Cockspur handles however they have different backsets dependent on the style of the window they're in. This is due to the fact that they have a spur that extends from the handle and is locked onto a cockspur wedge hitting plate.

Fit the New Handle

When you've picked a new handle, make sure you align it with the screw holes in the door and fix it using the supplied screws. Install the latch lever in similar fashion to the main handle in the event that you are replacing the door handles victorian handle. After that, attach the door trim once more to hide the screws for mounting.

Tips: To remove the head made of metal from the wooden wedge make sure the handle is held so that its broad end rests on the floor. Then use an hammer to tap the thin end of the handle. Be careful not damage the handle or handle spindle.