Reasons Your fiat 500 stolen without keys 500 Key Fob Won't Work

A key fob with the fiat remote key 500 number is a great way to unlock the doors and start the car. However, there are numerous reasons why the fob won't be working. These include a dead battery damage to the receiver module, problems, and interference.

This listing is for an NEW replacement Fiat 500x keys nottingham fiat 500x key fob Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't work is a dead battery. Modern key fobs have a very limited operating range, and must be within a few feet of the car to operate. If you are not within your vehicle and you press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) by a new key for fiat 500 one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They are available at your local hardware store or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your replacement fiat 500 key 500. The car will blink its parking lights and the key fob will operate the lock and unlock buttons.

If your key fob does not work after replacing the battery, there might be water damage that hinders it from interacting with the module in your vehicle. Water damage can happen in many ways, including simply splashing or submerging your key fob in saltwater at the beach. If you think your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this fails, you'll need to have the fob changed by an auto locksmith or a dealer.

Water Damage

While the fob has some rubber seals to keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually fail. If you get the fob wet, it's not a good idea but if you accidentally drop it into an empty cup of water, or do not remember to take it out of your pants pocket before running the washer do not give up hope.

First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Test the fob next to check if it's working. If the fob doesn't work, it may have to be reset. This is usually done by a dealer or professional auto locksmith.

If the key is older and has not been programmed to your car It will most likely need to be replaced completely. A professional automotive locksmith can complete this simple process. The locksmith will require the key to be cut to match your car's ignition. They'll also need to reprogram the fob to the system of your car. This is a quick and cost-effective process that can usually be completed on the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote's range is of 30 feet, which means in the event that you are far from your vehicle, it won't respond to your commands. You can remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly called a "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob will solve the problem. The instructions are available for most vehicles on YouTube or in the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, they could stop the coin battery from being properly seated and result in the malfunction of your remote.

In rare instances the fob could be desync'd with your vehicle due to software problems or hardware issues. This can be a major issue, but you are able to frequently fix this issue by visiting an auto locksmith to have them reprogram your fob. In certain instances, they may need to reinstall the program in your body control module, as well.

Interference

In addition to a dead coin battery The key fob might not be receiving or transmitting a signal due to interference. This could happen if the key fob is close to the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob may not work because of a weak connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, it could have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands which are then processed by the vehicle.

There is a straightforward method to reset the 500's onboard system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear out any remaining electrical charge and restart the car's computer system, which can help you get your key fob working again. If the issue continues, you should seek the advice of an expert technician. They will be able diagnose the root of any issues.