Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain, durable and long-lasting. They do not get rotten or rusty like aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. It is crucial to take the time to make sure that you're doing all you can to keep your windows in good condition.

Single-pane windows are fairly simple to replace, and they generally fit into frames that were previously in use very easily. If you have double-paned windows which are joined by internal beading, it will be more difficult to remove and replace the old panes. In this situation it is essential to purchase plastic spacers to help the new pane fit into the window frame.

If you plan to try to remove the glass panes yourself it is important to wear appropriate safety gear that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a dropcloth prior to you begin working on the window panes, so that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled.

It's a great idea to tape the gap once the glass has been removed. This will prevent water and drafts from entering your property until a professional arrives to fix the window. This will also act as a barrier that will prevent any intruders from getting access to your home. If the gap between the door and the window is significant, you may need to consider an alarm system that includes an opening. This will provide the best of both.

2. Sagging

uPVC is durable, energy-efficient and affordable alternative to timber sash window. However, over time they can suffer from a variety of issues, including sagging. A sagging uPVC window can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to lose its shape, it is important to act swiftly to prevent the problem from getting worse.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to open the windows so you can access the frame. Then, using a screwdriver, you can take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, shut your window and check for fit. If you're satisfied with the fit of your window, you can tighten screws to hold them in the right position.

If you can't reposition the hinges you may need to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to loosen. If this happens, it's important to replace the seal as quickly as possible to ensure your uPVC windows remain watertight and safe from drafts.

uPVC handles may also become loose. Most often it is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has worn out. It's relatively simple to fix a loose uPVC hand. First, you'll need to close the window and perform an experiment fit. The corners of the sash need to align with the casing joint. If it doesn't, you can make use of a screwdriver to loosen the handle and turn the mechanism back into the position it was in.

3. Water Leaks

It is crucial to take action if you awake each day to find mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home, and impact your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

It is a fairly easy fix and should be undertaken by any DIY expert. Depending on the severity of the problem the caulking that was used up may need to be removed before a fresh layer can be applied. It is crucial to keep in mind that when it comes to uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area harder to clean and can decrease the efficiency of your energy usage.

It is crucial to make sure that any drainage holes are clear of debris and that the sill pan is angled properly so that it drains away from the window. In more serious instances, you may need to think about replacing the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

It is also important to note that if the leakage originates from the glass of your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be fixed by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open with a breeze It could be hinges that are at the fault. Any competent DIYer can replace the hinges in a matter of minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that are hinged and like any mechanical part they can wear down over time. It is very easy to change a window hinge but it's much easier if someone else helps hold the frame.

Check that the uPVC hinges open and close in the proper direction. Look for the arrows on each hinge to determine which way the window should be opened.

The issue could be caused by opening the window incorrectly or by a poor installation in the factory. Sending us photos via our website is often enough to solve the issue. We are always happy to give advice.

Regular lubrication of the hinges is essential. Applying a light engineering lubricant on the hinges is an ideal method to accomplish this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also reduce the possibility of a window sticking and help prevent corrosion. The ideal time to perform this every year. WD40 or other solvent-based oils should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. The hinges can also be unbalanced due to wear, which can cause gaps where the sash and frame meet. If they're beyond repair, it might be necessary to have them realigned. Secondly the interlock, this is on the hinge side of the window, can also be misaligned, and again it's possible to give them a thorough clean, however in some instances it could be necessary to get them replaced.

The next most common reason for draughts are the window seals, these are susceptible to being worn out or damaged over time, and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and will reduce the possibility of draughts.

Another method of reducing the amount of draughts is to use a draught-excluder. These are typically fabric tubes filled with a filler that can be placed over your window sill. They can keep your home warm by blocking out cold air.

With a little maintenance and repairs, your upvc window repairs windows will provide excellent security and insulation for your home. However, it is important to recognize that windows last for a certain period of time and they may reach a point where it is more cost-effective to replace them rather than repair them. If you encounter any issues with your window made of upvc it is recommended to speak with a professional as soon as you can.