Seat Alhambra Key Problems

seat spare key's jumbo family MPV is one of the best in the market when it comes to keeping resales value. And with a brand new model on sale it's even more impressive.

There are many reasons why your key fob may not function properly including dead coin battery or water damage, receiver module issues or signal interference. This article will walk you through the steps to get it working.

Water Damage

If your seat alhambra key fob can withstand washing cycles or a bath in the pool or ocean then it's probably equipped with an incredible waterproof chip, but be careful not to make this a routine since exposure to excessive water increases the risk of the key fob getting damaged. If the key fob ceases to working after exposure to clean water from the tap or rain, just take out the battery, clean the electronic component with a towel and allow it to dry completely before putting the battery back in. If the key fob was exposed to soapy or salty water it is recommended you clean the chip using isopropyl or an electronic cleaner.

Faulty Receiver Module

If you've tried the battery of a button cell and the key fob doesn't lock or unlock then it's likely the receiver module has discovered a problem. The good news is that it is a relatively simple repair that is inexpensive, you can simply remove the battery 12 volts for just a few minutes (first take off the negative cable and then press the horn button numerous times) to drain any residual electricity, and then connect it in reverse order e.g. positive cable first, then negative cable later.

ESP Warning Light If the ESP warning light is flashing, this is normal and indicates that the car is traveling on terrains where the traction of the road surface and tyres isn't optimal, like snow, gravel or lots of surface water. If the ESP light is always on, it means that there is a problem in the system. This can be diagnosed with a iCarsoft i908 seat OBD code reader kit. It will provide detailed information about the fault.

Dead Coin Battery

One of the most common reasons for the seat keys replacement (Check This Out) alhambra keys to stop functioning is a dead coin battery. The key fob contains a small button cell battery that keeps it powered. Replace it with a brand new battery that has the exact size, voltage, and specifications as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts on the key fob are free of corrosion and clean.

If the key fob has been exposed water, like soapy or rain, it's recommended that you take the battery off and clean the electronic chip using isopropyl alcohol or an electronic cleaner prior to putting in the new battery. The chip could be permanently damaged by water. If the key fob still doesn't work after replacing the battery, it could be necessary to replace the key fob.

Faulty Receiver Module

If your key fob was not working after replacing the battery but it did not work, or stopped working suddenly your receiver module might be experiencing a problem. The receiver module is responsible for absorbing the radio frequency signals that are sent by your remote key fob and changing them into electrical signals that are then utilized by other modules in the car.

If the receiver module has developed a fault that prevents it from responding to any of the commands issued by your remote key fob. In this scenario, you will be required to visit a service for reprogramming the key fob, and also a new receiver module.

The key fob is fitted with rubber seals to prevent water from entering the chip inside. If you immerse the key fob in soapy or salty water, it may damage the chips. If your key fob doesn't work, you can try cleaning the chip using isopropyl or an electronic cleaner.

If the keys have been paired but the receiver module has developed a fault, you can try rebooting all of the onboard electronics by disconnecting the battery with 12 volts for a short period of time. Then reconnect the battery in reverse order (negative cable first, then positive). This will reset all the electronics onboard and will bring them back into operation.

A malfunctioning electronic chip

The key fob is equipped with a chip that transmits the signal from the key to the receiver module every time the key is used. If the signal doesn't match that stored by the car the immobilizer is able to shut off the engine and prevent the vehicle from starting. If the key fob does not work and you aren't able to reprogram it, this could be due to a faulty microchip.

The chip inside the key fob may have to be altered to make it work again. The best way to do this is to remove the key from its housing and using a pin needle to contact each of the retaining clips made of steel. If these clips are damaged or broken, you will require replacement to allow the remote control to function. Make sure that the replacement batteries are the same size, voltage and specification as the original.

The Seat Alhambra is a well-designed and popular model but, as with any car, it can sometimes experience issues with certain components or equipment. For instance there are owners who have had issues with the automatic climate control system, which could malfunction and cause problems in a specific setting. In the same way, the infotainment system has also been known to malfunction and freeze screens.