Reasons Your fiat 500 flip key repair (http://bitetheass.com) 500 Key Fob Won't Work

A fiat 500 key fob is a convenient way to open the doors and start the car. There are a variety of reasons why the fob may stop working. This could be due to a dead battery and water damage, as well as problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat key cover Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is due to an inactive battery. Modern key fobs offer only a limited range of operation and must be within a few inches of the vehicle to function. If you're far from your vehicle and fiat 500 flip key repair you press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) by a new one from a reliable brand such as Panasonic, Duracell, or Energizer. They can be found in the local hardware store or on the internet.

After you've replaced the battery in the coin cell It is possible to test it by standing near your fiat punto keys 500 and pressing the buttons. The car will flash its parking lights and the key fob should operate the lock and unlock buttons.

If the fob's remote doesn't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module inside your car. Water damage can happen through a variety of methods, including a simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work the fob might need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the chip's electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short, Fiat 500 Flip Key Repair and eventually fail. It's not a good thing to soak the fob in water, but don't give it up even if you accidentally drop the fob in water or fail to remove it from your pocket.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Check the fob to verify if it's working. If the key still doesn't work, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key is newer and was not programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will require the key cut to match the car's ignition. They'll also need to reprogram the fob in the car's system. This is a quick and cost-effective procedure that is usually completed within the same day.

Receiver Module Issues

One of the main reasons your 500 key fob won't be functioning is because it's out of range. The remote typically has 30 feet of range or less and if it's far from your vehicle, it will not respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board problem. In most cases, reprogramming the fob will solve the issue. There are instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin battery. If they loose tension they could stop the battery from being properly seated and could result in the malfunction of your remote.

In rare cases the fob could be desync'd with your vehicle due to software or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software might require reinstallation to your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive an signal due to interference. This could occur if the key fob is in proximity to radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob could not function may be a lack of connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing the battery, reprogramming, and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module, located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands, which are then read by the vehicle.

There's a quick and easy way to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers. This could allow you to get your key fob working again. If the issue persists, you should speak with an expert technician. They will be able diagnose the root cause of any issues.