Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it may be time to replace the battery. If you do replace the battery and Remote it continues to stop working, then the problem may be elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and components required for this type of service.

Dead Coin Battery

The most frequent reason that your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The battery of the coin cell inside the key fob will drain quickly in the event that you don't use it often enough. If your remote started to show signs of weakening such as a loss in range, and then stopped working completely it is likely that the battery is dead.

The battery inside the key fob is secured by metal clips that hold it in place. If the clips are loose, it could lead to contact issues which will prevent the remote from receiving power. Use a flathead screwdriver pry open the retaining clip and remove the battery. Make sure that the battery you choose to use has the same size, voltage and specifications as the original.

The key fob may also become corroded or damaged by exposure to water. Even a short bath in soapy, warm water can cause damage to the chip. Make sure your key fob is dry.

Water Damage

Water damage could be the cause of your key fob not working properly. The rubber seals on key fobs stop them from getting damaged by a light splash or drizzle of water. However, it's crucial to keep your keys of your car away from the washing machine, the ocean, and pool.

The key fob is equipped with an electronic chip in it that sends a signal car's immobilizer system. This is what allows your 500 to lock or start, but should the chip become saturated, it won't be able to longer function.

You can clean your key fob's internal electronics with isopropyl Alcohol or an electronic cleaner to see whether they're still working. It is best to replace the key fob when it's submerged into salt water instead of trying to repair it yourself.

While a replacement fob could cost you a bit of money, it is much less expensive than having to pay for your Fiat 500 to be towed to the dealer and repaired! You could also do it yourself with only a few steps. Make sure you have the correct type of battery before you attempt to open your key fob. You can find step-bystep instructions for any car keyfob on the internet.

Faulty Chip

The chip that is contained in the key fob communicates with your car's immobiliser unit to make sure the car is capable of starting when the correct key is inserted. If the chip is damaged, or damaged in any way, your car will not start.

A chip that is defective can happen due to a variety of reasons but the most common cause is water damage or an unresponsive battery. It is best to hand over the job to a professional locksmith, who can replace the chip quickly and at an affordable cost.

If your key fob will not function after being exposed to clean water from a tap or rain take it off the battery. Wipe down the electronic component with an old towel. If the key fob fails to work it's likely to be a fried chip and is required to be replaced.

Some people will go to their dealer when in need of a new fiat 500 locked keys in car key fob, but this could be a costly option. If you are seeking a cost-effective method to get your Fiat key fob fixed Look no further than United Locksmith. We have the tools and experience necessary to repair your Fiat key fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle that can unlock and lock doors (and start the car if it has an automatic transmission) up to 50 feet. However, there are a few factors that can cause the fob to cease working. This includes a dead battery, water damage, worn-out buttons or a receiver issue signal interference or malfunctioning chips.

If the fob is in a pocket which has experienced extreme trauma, such as falling on hard floor or remote being washed in a washing machine, it may not be able to communicate with the car's Body Control Module (BCM). The BCM is a security system that will only accept signals from genuine keys.

It is necessary to replace the fob in case this occurs. A locksmith professional can handle every aspect of the key replacement procedure, including programming a new one for the 500. They can even give you the fob cloned to work exactly like the original (and costs only a fraction of the price).