Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They don't decay or rust as timber and aluminum.

It is crucial to wash and oil UPVC windows and doors regularly. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a huge amount of damage to your home, making it very dangerous and potentially fatal. It is important to make sure that your windows are in good working order.

For single pane windows it is relatively easy to replace them, and the new window will usually fit inside the frame that was previously installed easily. However If windows with double glazed window repairs panes are secured by internal beading, it'll be more difficult to remove the old panes and put in new ones. In this situation you'll need locate some plastic spacers that will help the new pane to fit correctly into the frame of the window.

Wearing eye protection and thick gloves is a must if you plan to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled under.

After the glass has been removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional can come out and fix the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap between the window and the door is large, you might prefer an alarm system that includes a window. This will give you the best of both.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. In time, they could develop a number of problems that include sliding. A sagging window can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to unblock the windows to reach the frame. With an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and test it for fit. If you're satisfied with the fit, tighten the screws to ensure they stay in place.

If you cannot reposition the hinges, you might have to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to loosen. It is essential to replace your seal as quickly as you can in order to ensure that your uPVC window watertight and draughtproof.

upvc window repairs near me handles can also become loose. This is often caused by screws that have become undone over time, but it could be caused by the handle mechanism wears out. It's fairly simple to repair a loose uPVC handle. First, you'll need to close the window and perform a test fitting. The joint at the corner of the sash must align with the joint on the casing. If it does not then you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism into position.

3. Water Leaks

If you awake to wet floors and damp walls each time it rains, it's crucial to take action. Water leaks from windows can not only cause degradation of your home's structure but also hamper your efforts to control the temperature inside your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on how serious the problem is, the old caulking may have to be removed. It is important to remember that when it is about uPVC window repairs, you should avoid the temptation to "over-caulk and then make the area harder to clean and could decrease the efficiency of your energy usage.

Check that any drainage holes have no debris in them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you might have to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

It is also important to remember that if the leakage is coming from between the glass in your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sliding. A uPVC specialist can fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and open with a breeze It could be the hinges that are at fault. They can be easily repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical part hinges will be damaged over time. It is very easy to replace a hinge on a window but it's much easier if someone helps you hold the frame.

Check that the uPVC hinges are closed and open in the proper direction. You can check this by looking for the arrow on each hinge. This shows which way the window should be opened.

The problem can be caused by opening the window improperly or due to a poor installation in the factory. This can often be resolved by sending us a photograph through our website and we will be happy to give you suggestions.

Regular lubrication of the hinges is essential. Applying a light engineering lubricant to the hinges is a great method of doing this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It can also lower the risk of a window getting stuck and stop corrosion. Ideally, you should do this at least once a year. WD40 and other solvent based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by different factors. The hinges may also become unbalanced due to wear, causing a gap where the sash and frame meet. If they're beyond repair, it might be necessary to get them re-aligned. The interlock may also become misaligned. This happens on the hinge side and may need to be cleaned. In certain instances it might be necessary to replace these.

These seals are susceptible to wear and tear or be damaged over time, allowing air escape. Replacement of these with high-quality weatherstripping will help to keep draughts at bay. Another option is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and again will reduce draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler, which can be put on top of your window sill. They can help stop cold air from entering and keep your home warm and cozy!

With a bit of regular maintenance and repairs your windows made of upvc will continue to provide excellent security and insulation for your home. However, it is important to realize that windows last for a certain period of time and there may come a point where it is more cost-effective to replace them rather than fix them. If you are having issues with your upvc windows, it is best to seek professional assistance immediately.