Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain, durable and long-lasting. They are not susceptible to get rotten or rusty like aluminum or timber.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home, and could even be fatal. It is crucial to take the time to ensure that you're doing all you can to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace, and they generally fit into old frames very easily. However If you have double pane windows that are held in place by internal beading, it'll be more difficult to get rid of the old panes and put in new ones. In this case it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you plan to try to remove the glass panes yourself it is important to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not on the floor, where they could be trampled.

After the glass has been removed and the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from entering the property until a professional comes out and fix the window. This will also act as a barrier that will prevent any intruders from getting access to your home. If the gap is large, you might want to consider using a security door that has an integrated window, as this will offer the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable, durable and energy-efficient alternative to timber windows with sash. However, over time they are susceptible to a range of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from worsening.

To fix a window that is sagging you can try repositioning the hinges. To do this, you'll need open the window to get to the frame. Then, using an screwdriver, take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close the window and verify the fitting. If you're satisfied with the fit, you can tighten the screws until they stay in position.

If you are unable to reposition the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out and cause their tightness to decrease. It is essential to replace your seal as soon as you can in order to keep your upvc window repairs window watertight and draughtproof.

uPVC handles can also loosen up. The majority of the time, this is caused by screws that have become loose over time. However, it can also happen because the handle mechanism has worn out. It's relatively simple to fix a loose uPVC handle. You'll first need to close the window and perform an experiment fitting. The corners of the sash should align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and reverse the mechanism back into position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls every time it rains it's crucial to take action. Water leaks from windows are not just a cause for degradation of your home's structure but also undermine your efforts to regulate the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or not present.

This is a simple fix that can be done by any DIYer who has the ability. Based on the severity of the issue the caulking that was used up may need to be removed before a new layer of caulk is applied. It is crucial to remember that when it is about uPVC window repairs, you should not be tempted to apply too much caulk' as this will only make the area harder to clean and can reduce the efficiency of your energy.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely the issue is with the seal rather than the frame. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open with a breeze It could be hinges at fault. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Like any mechanical component hinges will wear out over time. It's easy to change the hinges on a window but it's much simpler if you have someone to help you hold the frame.

It is also important to ensure that the uPVC hinges are opening and closed in the right direction. Check for the arrows on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a particular way or by inadequate installation at the factory. Sending us a photo via our website will often resolve the problem. We are more than happy to give suggestions.

It is also important to ensure that the hinges are lubricated regularly. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regularly lubrication makes the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. Ideally, you should do this once a year. WD40 or other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by various factors. The hinges can also be unbalanced due to wear, creating gaps between the frame and sash. This can be easily fixed by giving them a good clean, but if they are beyond repair it could be necessary to get them re-aligned or replaced. In addition, the interlock could be disaligned. This happens on the hinge side and could require to be cleaned. In some instances it might be necessary to replace the hinges.

The next most common reason for draughts are the window seals. They are susceptible to being worn out or damaged over time and will allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. this will help to regulate indoor temperatures, and also lessen the risk of draughts.

One of the most effective ways to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes that are filled with some kind of filler. They can be put on the windowsill on top. They can keep your home warm by blocking cold air.

With a little regular maintenance and repairs, your upvc windows will provide excellent insulation and security for your home. It is crucial to keep in mind that all windows will eventually become worn out, and it is more cost-effective to simply replace them rather than repair them. So, if you're having issues with your upvc windows, it is always best to seek professional assistance as soon as possible.