Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to rot or rust like timber and aluminum.

It is essential to clean and oil UPVC windows and doors regularly. This will help avoid unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, making it very hazardous and possibly fatal. You should take the time to make sure that your windows are in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. If windows with double panes are joined by internal beading, it will be harder to remove and replace the panes that were previously in use. In this case, it is necessary to purchase plastic spacers in order to make sure that the new pane fits into the window frame.

If you're planning to try to remove the window panes yourself it is important to wear the proper safety gear, including thick gloves and protective eyewear. You should also lay down a dropcloth before you begin working on the window panes so that any shards of glass fall onto the fabric, not onto the floor and could be trampled.

Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to block water and drafts from entering the property until a professional is able to come out and fix the window. It also acts as a barrier, preventing any intruders from gaining entry into your home. If the gap between the door and the window is substantial, you may prefer security screens that includes windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows made of sash. However, over time they can suffer from a variety of issues like sagging. A window that is sagging can cause problems with light, draughts, and even security. It's important to take action when you discover that your uPVC windows are falling down.

Repositioning the hinges could help fix a window that is sagging. First, you'll need to unblock the windows to access the frame. Then, remove both the hinges on the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, close your window and test it for fit. If you're satisfied with the fit, tighten the screws until they remain in place.

If you are unable to move the hinges, you might have to replace the seal. Over time rubber seals can lose their elasticity and become dry which causes their tightness to decrease. If this happens, it's essential to replace the seal as quickly as possible so that your uPVC windows are watertight and safe from drafts.

UPVC handles can also loosen. This is usually due to screws that have loosened over time, but it can also be due to the mechanism of the handle wears out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, you'll need to shut the window and then perform a test fitting. The joint at the corner of the sash should align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

It is essential to take action if you awake each day to discover mouldy walls and wet floors. Water leaks through windows can cause structural damage to your home and hinder your ability to control the temperature inside your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a relatively easy fix that can be completed by any competent DIYer. Based on the severity of the problem the old caulking may need to be removed before a fresh layer can be put on. When it comes to uPVC repair, it is important to be careful not to over-caulk. This will make your window more difficult to clean and decrease its energy efficiency.

Check that any drainage holes have no debris inside them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives in damp conditions and can quickly spread across the house.

If the leakage occurs between the double-glazed glass, it is more likely the issue is with the seal rather than the frame. This can be easily repaired by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window repair Windsor is difficult to open or if it blows open with the breeze. They can be repaired by any skilled DIYer and can be completed in a matter of minutes.

Almost every household in the UK will have either top hung or side hung uPVC windows that are hinged and, like all mechanical parts, they can wear down over time. It's easy to change a window hinge but it's much simpler if you have someone to help hold the frame.

Verify that the uPVC hinges are closed and open in the proper direction. Look for the arrows on each hinge to determine the direction in which the Window Repair Leatherhead should be opened.

The issue can be caused due to opening the window in the wrong way or a faulty installation in the factory. Sending us a picture via our website is often enough to resolve the problem. We are always happy to offer suggestions.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also lower the possibility of a window sticking and help prevent corrosion. Ideally, you should perform this every year. WD40 and other solvent-based oils are not recommended because they can damage the parts of your uPVC window repair Weybridge.

5. Draughts

Draughts in Upvc windows can be caused by different things. The hinges may also become misaligned due to wear, creating an opening where the sash meets frame. If they're beyond repair, it could be necessary to get them re-aligned. The second is the interlock, which is on the hinge side of the window, may also become misaligned, again it may be possible to give them a clean but in some instances it could be necessary to have these replaced.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. this will help in regulating indoor temperatures and again will reduce draughts.

Another, and most effective methods to reduce the draughts in your home is to use an draught excluder. These are usually fabric tubes which are filled with a type of filler. They can be positioned on the windowsill on top. They will help keep cold air out and keep your home warm and cosy!

Your upvc windows can keep providing excellent insulation and security to your home with a little regular maintenance and repairs. However, it is important to recognize that all windows have a lifespan and there may come a point where it is more economical to replace them than repair them. If you are having issues with your upvc windows, it is recommended to seek assistance from a professional immediately.