Double Glazing Door Lock Repairs

Is your uPVC door or window mechanism faulty? Perhaps the window or door handles aren't aligned properly or are difficult to use.

You will lose energy if your double-glazed doors don't function properly. This also increases the chance of burglary. Owen the Locksmith can fix your door lock at an affordable price.

Snapped Key

When a key snaps off inside the lock, it can be extremely frustrating. It's also potentially a security risk, as the door may not be locked and make you vulnerable to intruders. Fortunately, there are simple fixes you can attempt to fix the problem and get your door functioning properly again.

First, remember to stay calm. If you panic and begin playing around with your keys, you might just end up pushing the damaged piece of the key further into the lock, double glazing repair thereby making the situation much worse.

Then spray WD-40 or another penetrating oil into the lock to make the broken piece slip out more easily. You can also make use of a screwdriver to break pieces that might be blocking the way. If you're fortunate enough to have a bit of the key left visible it, you can make use of a paperclip or other thin metal object to grab it and pull it out. Both methods work well, however, be very careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you do not have any of these handy, you can use needle-nose pliers that bend to create hooks. Additionally, a pair of tweezers is a good way to grasp and pull out the last piece of the key that was broken.

If you are unable to remove the broken key piece Use a lock deicer. It's available at most hardware stores and is used to freeze any moisture that may be present within the lock.

If none of these solutions work, it may be time to consult a locksmith. Fitlocks experts can quickly fix problems such as broken handles and snapped keys with uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are more easy to use. Book a double glazing repair with us online or give us a call to discuss your requirements.

Broken Cylinder

A damaged cylinder can pose an immediate security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. A locksmith must tap the cylinder to repair it. They can do this with an hammer or another tool, but the best method is to make use of an extended match or piece of wire. Then, place the match's end or wire close to the keyway. The locksmith can then strike the lock in order to crack it. This is superior to using a hammer that could damage the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can occur when the cylinder block as well as the cylinder head are made of various metals, like cast iron and aluminium. Different metals can heat up and cool off at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.

Another possible cause for cracks in the cylinder is corrosion. If the cylinder head as well as cylinder block are not maintained properly, this could lead to rusting or corrosion and cause them to expand at a greater rates than they should. In time, this could cause cracks.

If your uPVC window or door lock is rigid and requires a lot of pressure to turn it could be due to a variety reasons. This problem can be caused by a malfunctioning locking mechanism, or misalignment and also a worn out handle.

Fortunately it is a simple and affordable fix for the majority of double glazing owners. A professional locksmith is able to solve this issue within an hour of arriving at your home. Based on your requirements they can change the locking mechanism, change the window handles, and change the gearboxes. A locksmith with experience will always be able advise you on the most cost-effective options for your home. They can even suggest upgrades to 3 Star security TS007 euro cylinders that will give you an additional layer of protection against burglars. It's a small price to enjoy the peace of mind that comes from knowing your uPVC door is secure.

Broken Handle

Window handle locks are complex mechanisms that deteriorate with time and use, so it's no surprise that they can break. It isn't easy to determine the reason behind the problem and repair it correctly.

The issue could be with the internal locking mechanism or the latch, fixing your broken handle can improve your upvc repairs near me double glazing door's security as well as help you stop the draughts. It can be expensive to replace or repair the handle in a way that isn't done correctly. It can also harm the frame and lock of your door.

Screwdriver When the window is open and the screw loose, loosen the handle. It should be located on the inside face of the back plate, and is normally concealed by a screw cover for aesthetic reasons. It is important to not lose any internal components of the handle such as the plates and levers on either side. Ideally, keep these in the same place so you can re-install them if needed.

Then, rotate the handle so it's at 90 degrees to the window frame and loosen the screw at the back of the handle that fixes it to the internal spindle by using a second screwdriver. Once the screw is loose, you can take the handle off and remove the broken spindle. Replace it with a brand new spindle, making sure it's the same length (you can find them online or in hardware stores). Screw it in place. Don't over tighten the screw as this could harm the handle as well as the window frame.

Make sure the new handle is fitted, then close and test the handle. It is likely that it will operate smoothly and you'll be able unlock your window.

Make sure to check that your uPVC window is closing properly when you're using the handle. If they don't then you may experience damp and draughts inside your home as in addition to compromising the efficiency of your home's energy usage. Core Sash Windows is a local window doctor near me company that can adjust the hinges on the frames of your windows to ensure that they shut correctly.

Broken Spindle

It is more common for the spindle to break than the handle. This is most typical in uPVC tilt and turn windows. These types of windows require a handle that operates a locking mechanism in the frame of the window. The handle is attached a central rod which activates cams with a mushroom shape that secure into the frame of the window keep. If the dead latch mechanism fails to open after the handle has been turned, it is likely the spindle has been damaged. This could be a problem that is frustrating.

Luckily there are steps that can be taken to rectify this issue. A good locksmith can quickly and efficiently fix this problem. A good locksmith will be able to disassemble the window's handle using a tool that removes the wheel portion where the spindle is located. This can be done without causing any damage to the handle or causing any other damage to the frame of the window.

After the wheel has been removed, the technician can inspect the spindle to determine what has caused it to break. This involves disassembling the spindle, and then examining every component, observing any wear or Double glazing repair damage. This procedure is usually carried out in a clean, well-lit room by highly skilled technicians.

Next, clean the damaged spindle. This will help get rid of any dirt or debris which might be preventing it from functioning normally. After this the spindle could be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is comparable in size to the original. He will then drill matching holes into both pieces. This will ensure that the spindle is perfectly matched with the handle.

If the damaged spindle cannot be repaired, it could need to be replaced entirely. Home centres sell generic substitutes but if the window design is unique then you'll have to speak with an expert in cabinet making or woodworking who can replicate the exact part. Once the new spindle has been installed it can be attached to the handle by line up the screw holes in the handle and the frame existing screws. Once the handle is set, you are able to operate your uPVC windows.